Advanced Adjustments/Settings
This chapter explains how to adjust and configure monitor settings in detail using the Setting menu.
For basic functions, see Basic Adjustment/Setting.
Basic Operation of the Setting Menu
- Press any switch (except
). - The operation guide appears.
- Select
. - The Setting menu appears.
- Select a menu to adjust/set with

and select
. - The Sub menu appears.
- Select a menu to adjust/set with

and select
. - The Adjustment/Setting menu appears.
- Perform adjustment/setting with

or 
and select
to accept the changes. - The sub menu appears.
- Selecting
several times will close the Setting menu.
Setting Menu Functions
Color
The color mode settings can be adjusted according to personal preference. The adjusted settings are saved for each color mode.

Functions that can be adjusted differ depending on the color mode.
✓: Adjustable, -: Not adjustable
Function | Color Mode | |||||||
|---|---|---|---|---|---|---|---|---|
User1 | User2 | Eco | sRGB | Paper | BT.709 | DICOM | ||
Brightness | ✓ | ✓ | - | ✓ | ✓ | ✓ | - | |
Contrast | ✓ | ✓ | ✓ | - | - | - | - | |
Temperature | ✓ | ✓ | ✓ | - | ✓ | ✓ | - | |
Gamma | ✓ | ✓ | ✓ | - | - | ✓ | - | |
Advanced Settings | Overdrive | ✓ | ✓ | - | - | - | - | - |
Hue | ✓ | ✓ | ✓ | - | - | - | - | |
Saturation | ✓ | ✓ | ✓ | - | - | - | - | |
Gain | ✓ | ✓ | ✓ | - | - | ✓ | - | |
Reset | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | - | |
Attention
- It takes about 30 minutes for the monitor display to stabilize. Please wait 30 minutes or more after power to the monitor has been turned on before adjusting the monitor.
- The same image may be observed in different colors on multiple monitors due to monitor-specific characteristics. To match the colors of multiple monitors, follow the steps below to make the adjustments.
- Display a white screen on each monitor.
- Use one of the monitors as a visual reference point to make adjustments to "Brightness," "Temperature," and "Gain" on the other monitors.
- When Auto EcoView is set to "On," the same brightness setting is shared by all of the color modes and cannot be set individually for each color mode (except for DICOM mode).
Color Mode
Settings: "User1" / "User2" / "Eco" / "sRGB" / "Paper" / "BT.709" / "DICOM"
Switch to the mode that suits the usage of the monitor.
The color mode settings can also be adjusted according to personal preference. Select the color mode for adjustment and perform adjustment using the relevant functions.
Note
- The items that can be adjusted are restricted based on the color mode setting.
- For details on the adjustment status of each color mode, see Switching Display Modes (Color Modes).
Brightness
Settings: "0" – "100"
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back panel).
Note
- If the image is too dark even when the brightness is set to 100, adjust the contrast.
Contrast
Settings: "0" – "100"
You can adjust the brightness of the screen by varying the video signal level.
Note
- When the contrast is set to 50, all color gradations will be displayed.
- When adjusting the monitor, it is recommended to perform brightness adjustment, which does not lose gradation characteristics, prior to contrast adjustment.
- Perform contrast adjustment in the following cases:
- If the image is too dark even when the brightness is set to 100 (Set the contrast to higher than 50.)
Temperature
Settings: "Off" / "4000K" – "10000K" (in increments of 500K, including 9300K)
Adjusts the color temperature.
The color temperature is normally used to express the hue of "White" and/or "Black" with a numerical value. The value is expressed in degrees "K" (Kelvin).
The screen becomes reddish at low color temperatures and bluish at high color temperatures, similar to the temperatures of a flame. A gain preset value is set for each color temperature setting value.
Note
- The value shown in "K" is available only as a reference.
- "Gain" allows you to perform more advanced adjustment.
- If set to "Off," the image is displayed in the preset color of the LCD panel (Gain: 100 for each RGB channel).
- When the gain is changed, the color temperature setting changes to "Off."
Gamma
Settings: "1.8" / "2.0" / "2.2" / "2.4"
Adjusts the gamma.
While the brightness of the monitor varies depending on the video level of the input signal, the variation rate is not directly proportional to the input signal. Maintaining the balance between the input signal and brightness of the monitor is referred to as Gamma correction.
Note
- If "sRGB" is selected for the color mode, "sRGB" is displayed for the gamma value.
- If "Paper" is selected for the color mode, "Paper" is displayed for the gamma value.
- If "DICOM" is selected for the color mode, "DICOM" is displayed for the gamma value.
Advanced Settings - Overdrive
Settings: "Enhanced" / "Standard" / "Off"
This function allows you to set the overdrive intensity based on the use of the monitor.
Image lag can be reduced by using the "Enhanced" setting when displaying moving images.
Advanced Settings - Hue
Settings: "-50" – "50"
Adjusts the hue.
Note
- Using this function may prevent some color gradations from being able to be displayed.
Advanced Settings - Saturation
Settings: "-50" – "50"
Adjusts the color saturation.
Note
- Using this function may prevent some color gradations from being able to be displayed.
- The minimum value (-50) changes the screen to monochrome.
Advanced Settings - Gain
Settings: "0" – "100"
The brightness of each red, green, and blue color component is referred to as Gain. The hue of "white" can be changed by adjusting the gain.
Note
- Using this function may prevent some color gradations from being able to be displayed.
- The gain value changes according to the color temperature.
- When the gain is changed, the color temperature setting changes to "Off."
Reset
Resets any color adjustments for the currently selected color mode back to the default settings.
Note
- If "Color" of "Multi-monitor Sync" is set to "Enable," the reset setting values will also be applied to other monitors (see Multi-monitor Sync - Color).
Signal
Set the details regarding input signal, such as the screen size and color format.
Picture Expansion
Settings: "Auto*1" / "Full Screen" / "Aspect Ratio"
- Only enabled during HDMI® signal input
The screen size of the monitor display can be changed.
- "Auto"
- The monitor automatically changes the screen size according to the aspect ratio and resolution information from the PC.
- "Full Screen"
- Displays images in full screen. Since aspect ratios are not maintained, images may be distorted in some cases.
- "Aspect Ratio"
- Images are stretched to full screen. However, because the aspect ratio of the displayed image is fixed, blank areas may remain horizontally.
Note
- Setting examples
- If the display is shown at the recommended resolution or if the PC controls the display size, the display size does not change even if you adjust the screen enlargement settings.
Sharpness
Settings: "Off" / "1" / "2"
When a low-resolution image is displayed using picture expansion mode ("Full Screen" or "Aspect Ratio"), the text and lines of the image may appear blurry. This blurriness can be reduced.
Note
- Depending on the display resolution, it may be difficult to notice differences caused by setting changes.
Input Color Format
Settings: "Auto" / "YUV" / "RGB"
The color format of the input signal can be specified.
Try changing this setting if colors are not displayed correctly.
Note
- Depending on the displayed image, it may be difficult to notice the difference caused by changing the settings.
Input Range
Settings: "Auto" / "Full" / "Limited"
Depending on the video reproduction device, there may be a restriction on black and white video signal levels output to the monitor. This kind of signal is called Limited range. On the other hand, unlimited signals are called Full range.
- "Auto"
- Input signal brightness range is automatically judged and is displayed appropriately (recommended setting). Depending on the video reproduction device, Limited range and Full range may not be able to be judged by the monitor. In such a case, selecting "Full" or "Limited" will allow it to be displayed appropriately.
- "Full"
- To be selected in case of Full range signals. Appropriate display can be obtained when this is selected, in case both blacks and whites are corrupted.
- "Limited"
- To be selected in case of Limited range signals. If blacks look washed out and whites look dull, selecting this expands the signal output range to 0 – 255 for a proper display.
Preferences
The monitor settings can be configured to suit your usage environment or preferences.

Note
- If a power consumption warning message appears, select "OK" to proceed to the next operation (see The message "Changes to this setting may increase power consumption." appears on the screen).
Auto Input Detection
Settings: "On" / "Off"
This function automatically recognizes the connector through which PC signals are input, and displays images on the screen accordingly.
- "On"
- When the monitor is connected to multiple PCs, if a specific PC enters sleep mode or no signal is input to the monitor, it automatically switches to another connector with an active signal.
- "Off"
- To be set to this when manually selecting input signals. Select the input signal to display using the operation switch (
) on the front of the monitor. For details, see Switching Input Signals.
Note
- When this function is set to "On," the monitor enters standby mode only when no signals are input from all connected PCs.
Newest Input Priority
Settings: "On" / "Off"
When a signal cable is connected while the monitor is in normal operation mode (excluding standby mode), the display automatically switches to that input port.
Compatibility Mode
Settings: "On" / "Off"
If you want to avoid the following phenomena, set this function to "On."
- The positions of windows and icons are shifted when the monitor is turned off/on or has returned from standby (power saving) mode.
- The PC does not return from sleep when operating the mouse or keyboard.
- The PC resumes from sleep mode when using the mouse or keyboard, but the monitor does not recover from standby mode.
- When the monitor is turned off, devices connected to the USB downstream ports will not operate or receive power.
Note
- If this function is set to "Off," the "Power" setting value of "Multi-monitor Sync" is set to "Disable."
USB-C Power Supply
Settings: "On" / "Off"
When connected via USB-C, you can stop the power supply (USB Power Delivery) to a laptop PC. To stop the power supply, set this function to "Off."
The setting value can be changed by pressing the operation switch (
) and power button simultaneously.

Note
- To use the charging function, the connected device must support device charging by using USB Power Delivery.
- Connected devices can be charged even when the monitor is in standby (power saving) mode.
- When "Compatibility Mode" is set to "On," connected devices can be charged even when the power of the monitor is turned off (see Compatibility Mode).
- Before changing the setting, remove all connected USB memory devices from the monitor. Otherwise, data may be lost or damaged.
- When the setting is changed, USB communication is temporarily disconnected and then reconnected.
VRR (Variable Refresh Rate)
Settings: "On" / "Off"
The monitor's refresh rate is automatically adjusted to match the frame rate rendered by the GPU, ensuring smooth image display.
Note
- To use this feature, your PC's VRR settings must be enabled.
- When changing the setting value, the screen may temporarily go blank and then reappear.
- If the display becomes unstable, set this function to "Off."
Signal Format - USB-C
Settings: "120Hz / USB 2.0" / "60Hz / USB 5Gbps"
For USB-C connection, you can switch between display refresh rate "120Hz / USB 2.0" and USB speed priority "60Hz / USB 5Gbps." Try changing this setting if the input signal is not displayed correctly or the intended display does not show.
Note
- This product supports USB 5Gbps. When connecting to peripheral devices that support USB 5Gbps, high-speed data communication is possible.
- The default setting is "120Hz / USB 2.0" and the maximum USB communication speed is 5 Gbps when set to "60Hz / USB 5Gbps."
- Before changing the setting, remove all connected USB memory devices from the monitor. Otherwise, data may be lost or damaged.
- When changing the setting value, the screen may temporarily go blank and then reappear.
Multi-monitor Sync
By connecting monitors that support this function to each other via USB-C, you can apply settings to multiple monitors simultaneously.

Multi-monitor Sync - Power
Settings: "Enable" / "Disable"
When the power status of one monitor is changed, that status is also applied to other monitors.
Note
- Monitors compatible with this function must be connected to each other via USB-C.
- To synchronize the power status, the setting value of "Power" on the receiving monitor must also be set to "Enable." If synchronization does not work correctly, check that the setting of "Multi-monitor Sync" is set to "Enable."
- Setting the value to "Enable" changes "Compatibility Mode" to "On."
Multi-monitor Sync - Color
Settings: "Enable" / "Disable"
When the setting value of Color Mode is changed, that setting value is also applied to other monitors.
Note
- Monitors compatible with this function must be connected to each other via USB-C.
- When monitors with the Auto EcoView function set to "On" are connected together, brightness is not synchronized. When synchronizing brightness using the Auto EcoView function, set Auto EcoView to "On" on only 1 of the connected monitors.
- Changes in brightness and gain settings due to EcoView Optimizer 2 are not synchronized.
- Even when color adjustments are synchronized, brightness setting values may not match due to individual differences between monitors.
- To apply the setting value of Color Mode to an additionally connected monitor, press "Apply to Others" on the source monitor.
Multi-monitor Sync - Apply to Others
Pressing "Apply to Others" displays a message. Selecting "OK" applies the setting values of "Power" and "Color" ("Enable" / "Disable") to other monitors.
When "Color" is set to "Enable," the setting value of Color Mode is applied to other monitors.
Advanced Settings - Standby Mode
Settings: "On" / "Off"
The monitor can be set to enter standby (power saving) mode according to the state of the PC.
The monitor enters standby mode after detecting that no signal is being input.
When the monitor enters standby mode, the screen will no longer be displayed.
- How to exit standby mode
- Press one of the operation switches (excluding
) on the front of the monitor - Send a signal to the monitor
Note
- Before entering standby mode, a message will be displayed notifying the transition.
- When not using the monitor, you can turn off the main power supply or disconnect the power plug so that the power is cut completely.
Advanced Settings - Speaker
Settings: "On" / "Off"
The audio output of the speakers can be switched between "On" and "Off."
Note
- If this function is set to "Off," you cannot adjust the speaker volume.
- When changing the setting value, the screen may temporarily go blank and then reappear.
Advanced Settings - Indicator
Settings: "Off" / "1" – "7"
The brightness of the power lamp can be set in normal operation mode or standby (power saving) mode.
The brightness increases as the number increases.
Note
- Even when the setting is "Off," the brightness will turn on at "1" in the following cases.
- The EIZO logo and certification standard logo is displayed on the screen
- The "No Signal" message is displayed on the screen
- Standby mode
Advanced Settings - Menu Rotation
Settings: "0°" / "90°" / "270°"
If you purchased the free mount specification model and the monitor is used in a portrait position, the orientation of the Setting menu can also be changed.
Note
- If you purchased the free mount specification model, you will need to adjust the PC settings to display the monitor in portrait mode. For details, refer to our web site.
How to check: Go to www.eizoglobal.com and type "vertical rotation" in the search box on the web site.
Advanced Settings - On-Screen Logo
Settings: "On" / "Off"
When the main power switch of this product is turned on and the power switch is activated for the first time, the EIZO logo and certification standard logo will appear on the screen. After that, they will not be displayed when turning the power switch off and on.
When this function is set to "Off," the logo does not appear.
Factory Reset
Restores the settings to the factory default settings.
EcoView Settings
See Conserving Energy.
Languages
Settings: "English" / "German" / "French" / "Spanish" / "Italian" / "Swedish" / "Japanese" / "Simplified Chinese" / "Traditional Chinese"
The display language for menus and messages can be changed.
Information
You can check the monitor information (model name, serial number (S/N), firmware version, usage time) and the input signal information.
Example:
When
is selected, the certification standard logo appears on the screen.