Advanced Adjustments/Settings

This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.

For basic functions, see Basic Adjustment/Setting.

Basic Operation of the Setting Menu

Touch any switch (except ).
The operation guide appears.
Select .
The Setting menu appears.
Select a menu to adjust/set with and select .
The Sub menu appears.
Select a menu to adjust/set with and select .
The Adjustment/Setting menu appears.
Perform adjustment/setting with or and select to accept the changes.
The sub menu appears.
Selecting several times will close the Setting menu.

Setting Menu Functions

Color

The color mode settings can be adjusted according to personal preference. The adjusted settings are saved for each color mode.

Functions that can be adjusted differ depending on the color mode.

✓: Adjustable, -: Not adjustable

Function		Color Mode
Function		User1	User2	sRGB	Paper	Movie	DICOM
Brightness		✓	✓	✓	✓	✓	-
Contrast		✓	✓	-	-	✓	-
Temperature		✓	✓	-	✓	✓	-
Gamma		✓	✓	-	-	-	-
Advanced Settings	Overdrive	✓	✓	-	-	-	-
	Hue	✓	✓	-	-	✓	-
	Saturation	✓	✓	-	-	✓	-
	Gain	✓	✓	-	-	-	-
Reset		✓	✓	✓	✓	✓	-

Attention

It takes about 30 minutes for the monitor display to stabilize. Please wait 30 minutes or more after power to the monitor has been turned on before adjusting the monitor.
The same image may be observed in different colors on multiple monitors due to monitor-specific characteristics. Make fine color adjustments visually when matching colors across multiple monitors. Follow the procedure below to adjust and match colors across multiple monitors.
Display a white screen on each monitor.
Use one of the monitors as a visual reference point to make adjustments to "Brightness," "Temperature," and "Gain" on the other monitors.
When Auto EcoView is set to "On," the same brightness setting is shared by all of the color modes and cannot be set individually for each color mode.

Color Mode

Settings: "User1" / "User2" / "sRGB" / "Paper" / "Movie" / "DICOM"

Select the desired mode according to the monitor application.

The color mode settings can also be adjusted according to personal preference. Select the color mode for adjustment and perform adjustment using the relevant functions.

Note

For details on the adjustment status of each color mode, see Switching Display Modes (Color Modes).

Brightness

Settings: "0" – "100"

The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back panel).

Note

If the image is too dark even when the brightness is set to 100, adjust the contrast.

Contrast

Settings: "0" – "100"

You can adjust the brightness of the screen by varying the video signal level.

Note

When the contrast is set to 50, all color gradations will be displayed.
When adjusting the monitor, it is recommended to perform brightness adjustment, which does not lose gradation characteristics, prior to contrast adjustment.
Perform contrast adjustment in the following cases:
If the image is too dark even when the brightness is set to 100 (Set the contrast to higher than 50).

Temperature

Settings: "Off" / "4000 K" – "10000 K" (in increments of 500 K, including 9300 K)

Adjusts the color temperature.

The color temperature is normally used to express the hue of "White" and/or "Black" with a numerical value. The value is expressed in degrees "K" (Kelvin).

The screen becomes reddish at low color temperatures and bluish at high color temperatures, similar to the temperatures of a flame. A gain preset value is set for each color temperature setting value.

Note

The value shown in "K" is available only as a reference.
"Gain" allows you to perform more advanced adjustment.
If set to "Off," the image is displayed in the preset color of the LCD panel (Gain: 100 for each RGB channel).
When the gain is changed, the color temperature setting changes to "Off."

Gamma

Settings: "1.8" / "2.0" / "2.2" / "2.4"

Adjusts the gamma.

While the brightness of the monitor varies depending on the video level of the input signal, the variation rate is not directly proportional to the input signal. Maintaining the balance between the input signal and brightness of the monitor is referred to as "Gamma correction."

Note

If "Paper" is selected for the color mode, "Paper" is displayed for the gamma value.
If "DICOM" is selected for the color mode, "DICOM" is displayed for the gamma value.

Advanced Settings - Overdrive

Settings: "Enhanced" / "Standard" / "Off"

This function allows you to set the overdrive intensity based on the use of the monitor.

Image lag can be reduced by using the "Enhanced" setting when displaying moving images.

Note

Depending on the display resolution and the setting of "Picture Expansion," overdrive may be set to "Off."

Advanced Settings - Hue

Settings: "-50" – "50"

Adjusts the hue.

Note

Using this function may prevent some color gradations from being able to be displayed.

Advanced Settings - Saturation

Settings: "-50" – "50"

Adjusts the color saturation.

Note

Using this function may prevent some color gradations from being able to be displayed.
The minimum value (-50) changes the screen to monochrome.

Advanced Settings - Gain

Settings: "0" – "100"

The brightness of each red, green, and blue color component is referred to as "Gain." The hue of "white" can be changed by adjusting the gain.

Note

Using this function may prevent some color gradations from being able to be displayed.
The gain value changes according to the color temperature.
When the gain is changed, the color temperature setting changes to "Off."

Reset

Resets any color adjustments for the currently selected color mode back to the default settings.

Signal

Set the details regarding input signal, such as the screen size and color format.

Window Selection

Settings: "Left" / "Right"

Select the screen to apply "Signal" to when using PbyP display.

Please perform this selection when starting usage of PbyP display.

"Left"
Applies settings to the left screen.
"Right"
Applies settings to the right screen.

Note

This can only be set when using PbyP display.
For information on PbyP, see Switching Input Signals.

Picture Expansion

Settings: "Auto^*1" / "Full Screen" / "Aspect Ratio" / "Dot by Dot"

Only available during HDMI signal input

The screen size of the monitor display can be changed.

"Auto"
The monitor automatically changes the screen size according to the aspect ratio and resolution information from the PC.
"Full Screen"
Displays images in full screen. Since aspect ratios are not maintained, images may be distorted in some cases.
"Aspect Ratio"
Displays images in full screen. Since aspect ratios are maintained, blank horizontal or vertical borders may appear.
"Dot by Dot"
Displays images at the set resolution or size specified by the input signal.

Note

Setting example
In the case of PbyP display, the setting is fixed to "Auto" for the HDMI signal and "Aspect Ratio" for the other signals.

Sharpness

Settings: "Off" / "1" / "2"

When a low-resolution image is displayed using picture expansion mode ("Full Screen" or "Aspect Ratio"), the text and lines of the image may appear blurry. This blurriness can be reduced by configuring the settings for sharpness.

Note

For some display resolutions, it is not necessary to configure the settings for sharpness. ("Sharpness" cannot be selected.)
Depending on the display resolution, it may be difficult to notice differences caused by setting changes.

Input Color Format

Settings: "Auto" / "YUV 4:2:2^*1" / "YUV 4:4:4^*1" / "YUV^*2" / "RGB"

The color format of the input signal can be specified.

Try changing this setting if colors are not displayed correctly.

Only available during HDMI signal input
Only valid for DisplayPort or USB-C signal input

Input Range

Settings: "Auto" / "Full" / "Limited"

Depending on the video reproduction device, there may be a restriction on black and white video signal levels output to the monitor. This kind of signal is called "Limited range." On the other hand, unlimited signals are called "Full range."

"Auto"
Input signal brightness range is automatically judged and is displayed appropriately (recommended setting). Depending on the video reproduction device, Limited range and Full range may not be able to be judged by the monitor. In such a case, selecting "Full" or "Limited" will allow it to be displayed appropriately.
"Full"
To be selected in case of Full range signals. Appropriate display can be obtained when this is selected, in case both blacks and whites are corrupted.
"Limited"
To be selected in case of Limited range signals. In case this is selected, the output signal range is expanded from 0 to 255 to obtain an appropriate display when black is pale and white is dull.

Note

When "Input Color Format" is selected in "YUV," the setting is automatically set to "Limited." Additionally, when "Auto" is selected and the monitor determines the input color format to be YUV, the setting is automatically set to "Limited."

Preferences

The monitor settings can be configured to suit your usage environment or preferences.

Auto Input Detection

Settings: "On" / "Off"

This function automatically recognizes the connector through which PC signals are input, and displays images on the screen accordingly.

"On"
When the monitor is connected to multiple PCs, if a specific PC enters power saving mode or no signals are input to the monitor, the connector is automatically changed to another one to which signals are input.
"Off"
To be set to this when manually selecting input signals. Select the input signal to display using the operation switch () on the front of the monitor. For details, see Switching Input Signals.

Note

Does not function in PbyP display.
This product automatically recognizes the connector through which PC signals are input, and displays images on the screen accordingly regardless of whether this function is set to On or Off just after the main power switch on the back of the monitor has been turned on.
When this function is set to "On," the monitor only enters the power saving mode when signals are not input from any PC.

Menu Rotation

Settings: "0°" / "90°" / "270°"

If you purchased the free mount specification model and the monitor is used in a portrait position, the direction of the Setting menu can also be changed.

Note

If you purchased the free mount specification model, you will need to adjust the PC settings to display the monitor in portrait mode. For details, refer to our web site.
How to check: Go to www.eizoglobal.com and type "vertical rotation" in the search box on the web site.
The menu cannot be rotated 180°. When rotating a monitor 180°, perform the adjustments/settings for the monitor before rotating it.

On-Screen Logo

Settings: "On" / "Off"

When the monitor is turned on, the EIZO logo and certification standard logo appears on the screen.

When this function is set to "Off," the logo does not appear.

Indicator

Settings: "Off" / "1" – "7"

The brightness of the power lamp can be set in normal operation mode or power saving mode.

The brightness increases as the number increases.

Note

Even when the setting is "Off," the brightness will turn on at "1" in the following cases.
The EIZO logo and certification standard logo is displayed on the screen
The "No Signal" message is displayed on the screen
Power saving mode

Sound Selection (PbyP)

Settings: "Left" / "Right"

Select the audio to be output from the monitor during PbyP display.

"Left"
Outputs the audio of the left screen.
"Right"
Outputs the audio of the right screen.

Note

This can only be set when using PbyP display.
For information on PbyP, see Switching Input Signals.

Signal Format - USB-C

Settings: "USB 5Gbps" / "USB 2.0 (480Mbps)"

For USB-C connection, you can switch between display signal priority "USB 2.0 (480Mbps)" and USB speed priority "USB 5Gbps" (see Signal Format - USB-C). Try changing this setting if the input signal is not displayed correctly or the intended display does not show.

Note

This product supports USB 5Gbps. When connecting to peripheral devices that support USB 5Gbps, high-speed data communication is possible.
The default setting is "USB 5Gbps" and the maximum USB transfer speed is 5 Gbps.

Advanced Settings - Compatibility Mode

Settings: "On" / "Off"

If you want to avoid the following phenomena, set this function to "On":

The positions of windows and icons are shifted when the monitor is turned off/on or has returned from the power saving mode.
The PC does not wake up from sleep mode even when operating the mouse or keyboard.
When the power to the monitor is turned off, a device connected to the USB-A (downstream) connector does not work, or power is not supplied to the connected device.

Advanced Settings - Power Save

Settings: "On" / "Off"

The monitor can be set to enter power saving mode according to the state of the PC.

The monitor changes to power saving mode about 15 seconds after signal input ceases to be detected.

When the monitor has shifted to power saving mode, images are not displayed on the screen.

How to exit power saving mode

Press the operation switches (excluding ) on the front of the monitor
The monitor automatically exits power saving mode when the monitor receives input

Note

Five seconds before the transition to power saving mode, a message will be displayed notifying the transition.
When not using the monitor, you can disconnect the power plug so that the power is cut completely.

Factory Reset

Restores the settings to the factory default settings.

Languages

Settings: "English" / "German" / "French" / "Spanish" / "Italian" / "Swedish" / "Japanese" / "Simplified Chinese" / "Traditional Chinese"

The display language for menus and messages can be changed.

Information

You can check the monitor information (model name, serial number (S/N), firmware version, usage time) and the input signal information.

Example:

When is selected, the certification standard logo appears on the screen.