Advanced Adjustments/Settings

This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu. For the basic setting functions using the buttons on the front of the monitor, see Basic Adjustments/Settings.

Basic Operation of the Setting Menu

  1. Touch any switch (except ).
  2. The operation guide appears.
  3. Select .
  4. The Setting menu appears.
  5. Select a menu to adjust/set with and select .
  6. The Sub menu appears.
  7. Select a menu to adjust/set with and select .
  8. The Adjustment/Setting menu appears.
  9. Perform adjustment/setting with or and select to accept the changes.
  10. The Sub menu appears.
    Selecting during adjustment/setting will cancel the adjustment/setting and restore the state prior to making changes.
  11. Selecting several times will terminate the Setting menu.

Setting Menu Functions

Signal

The signal settings are used to configure advanced settings for input signals, such as the color format and input range.

Signal Information

You can check the information for the input signal.

Pixel Inspection

See Pixel Inspection.

Input Color Format

Settings: "Auto" / "YUV 4:2:2*1" / "YUV 4:4:4*1" / "YUV*2" / "RGB"

  1. Only available during HDMI signal input
  2. Only valid for DisplayPort or USB-C signal input

The color space of the input signal can be specified.

Try changing this setting if colors are not displayed correctly. Normally, select "Auto".

YUV Color Matrix

Settings: "Auto" / "BT.601" / "BT.709" / "BT.2020"

Select the YUV format of the input signal. Use this setting for gradation collapse or other occurrences where the screen is displayed incorrectly because of a problem with the input signal.

Input Range

Settings: "Auto" / "Auto 109%" / "Full" / "Limited (109% White)" / "Limited" / "SDI Full"

Depending on the external device, the black and white levels in the video signal output to the monitor may be restricted. If the signal is displayed on the monitor in its restricted form, the blacks will be faint, the whites dull, and contrast will be reduced. The video range displayed on the monitor can be switched to make these signals the actual contrast ratio of the monitor.

Color

The setting details differ depending on the color mode selected.

When Color Mode is Standard Mode (User / BT.2020 / BT.709 / DCI-P3 / PQ_DCI-P3 / HLG_BT.2100 / Adobe RGB / sRGB / SYNC_SIGNAL)

Each color mode setting can be adjusted according to personal preference.

Attention
  • The same image may be seen in different colors on multiple monitors due to differences between individual monitors. Make fine color adjustment visually when matching colors on multiple monitors.
Note
  • If "Color Mode" is "SYNC_SIGNAL," the "Brightness," "Gamma (EOTF)," and "Color Gamut" are automatically set according to the input signal and cannot be changed.
  • Use the values in "Brightness" and "Temperature" as a guide.
Color Mode

Settings: "User" / "BT.2020" / "BT.709" / "DCI-P3" / "PQ_DCI-P3" / "HLG_BT.2100" / "Adobe RGB" / "sRGB" / "CAL" / "SYNC_SIGNAL"

Select the desired mode according to the monitor application.

Note
Brightness

Settings: "40 cd/㎡" – "450 cd/㎡"

The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back panel).

Note
  • If a value that cannot be set is selected, the value will appear in magenta. In such a case, change the value.
Temperature

Settings: "Native" / "4000 K" – "10000 K" / "D50" / "D65" / "DCI" / "User"

Adjusts the color temperature.

The color temperature is used to express the chromaticity of "White". The value is expressed in degrees "K" (Kelvin).

The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the temperature of a flame.

Specify a color temperature in units of 100 K, or select a standard name.

Note
  • Select "Native" to display the original colors of the LCD panel.
  • "Gain" allows you to perform more advanced adjustment. When gain is changed, the color temperature is changed to "User."
  • The gain preset values are set for each color temperature setting value.
Gamma (EOTF)

Settings: "1.6" – "2.7" / "sRGB" / "EBU(2.35)" / "PQ" / "HLG"

Adjust the gamma.

The brightness of the monitor varies depending on the input signal, however, the variation rate is not simply proportional to the input signal. The control performed to keep the balance between the input signal and the brightness of the monitor is called Gamma correction.

Set the gamma, or select a standard name.

Note
  • If you select "HLG," you must set "HLG System Gamma."
PQ Option

Settings: "300cd/㎡ Clipping" / "500cd/㎡ Emulation" / "1000cd/㎡ Emulation" / "4000cd/㎡ Emulation" / "10000cd/㎡ Emulation"

Areas with brightness equal to or greater than the value set here are displayed as clipping or emulation at this setting value for the PQ signal that is input to the monitor.

Note
HLG Option

Settings: "Off" / "HLG300"

When selecting "HLG300" with the brightness set to 300 cd/m2 for the HLG signal input to the monitor, any areas exceeding 300 cd/m2 will be clipped. Selecting "Off" will not clip these areas.

Note
  • This can be set when "HLG" is specified for "Gamma (EOTF)."
HLG System Gamma

Settings: "1.0" – "1.5"

Adjust the system gamma value for the HLG signal that is input to the monitor.

Note
  • This can be set when "HLG" is specified for "Gamma (EOTF)."
Color Gamut

Settings: "Native" / "Adobe RGB" / "sRGB" / "EBU" / "BT.709" / "BT.2020" / "SMPTE-C" / "DCI-P3"

Set the color reproduction area (color gamut) of the monitor.

"Color Gamut" is the range of colors that can be represented. Multiple standards are defined.

Note
  • Select "Native" to display the original color gamut of the LCD panel.
  • The method of displaying colors outside the monitor's displayable range within the defined color gamut can be set. For more information, see Advanced Settings - Gamut Clipping.
Advanced Settings - Hue

Settings: "-100" – "100"

The hue can be adjusted.

Note
  • Using this function may make some color gradations unavailable for display.
Advanced Settings - Saturation

Settings: "-100" – "100"

The saturation can be adjusted.

Note
  • Using this function may make some color gradations unavailable for display.
  • The minimum value (-100) changes the screen to monochrome.
Advanced Settings - Gamut Clipping

Settings: "On" / "Off"

The method of displaying colors outside the monitor's displayable range within the color gamut specified in accordance with Color Gamut can be set.

Note
  • The diagrams shown above are conceptual diagrams, and they do not display the actual color gamut of the monitor.
  • This setting will be disabled if "Native" is selected at Color Gamut.
Advanced Settings - XYZ Format

Settings: "On" / "Off"

If this function is set to "On," the XYZ signal for digital cinema can be displayed on the monitor.

Note
  • This can be set only when Color Gamut is set to "DCI-P3."
  • If you select "On," you cannot set "Color Gamut."
Advanced Settings - Gain

Settings: "0" – "2000"

The brightness of each color component red, green, and blue is called Gain. The chromaticity of "white" can be changed by adjusting the gain.

Note
  • Using this function may make some color gradations unavailable for display.
  • The gain value changes according to the color temperature.
  • When gain is changed, the color temperature is changed to "User."
Advanced Settings - Black Level

Settings: "0" – "1500"

You can adjust the brightness and chromaticity for black by adjusting the levels of red, green, and blue, or by adjusting all of the black levels. Display the black test pattern or the background and adjust the black level.

Advanced Settings - 6 Colors

Settings: "-100" – "100"

The hue, saturation and lightness (brightness) can each be adjusted for the colors Magenta, Red, Yellow, Green, Cyan, and Blue.

Reset

Resets any color adjustments for the currently selected color mode back to the default settings.

When Color Mode is Advanced Mode (CAL)

You can set targets for SelfCalibration and execute calibration.

Color Mode

Settings: "User" / "BT.2020" / "BT.709" / "DCI-P3" / "PQ_DCI-P3" / "HLG_BT.2100" / "Adobe RGB" / "sRGB" / "CAL" / "SYNC_SIGNAL"

Select the desired mode according to the monitor application.

Note
Target Settings - Brightness

Settings: "Min" / "40 cd/㎡" – "450 cd/㎡" / "Max"

Set the brightness that will be used as a calibration target for SelfCalibration.

Target Settings - Black Level

Settings: "Min" / "0.2" – "3.5"

Set the black level that will be used as a calibration target for SelfCalibration.

Target Settings - White Point - Temperature

Settings: "4000 K" – "10000 K" / "User" / "D50" / "D65" / "DCI"

Set the White Point that will be used as a calibration target for SelfCalibration.

Set the White Point using the color coordinates (White(x) / White(y)) or color temperature.

When specifying color coordinates, set the values for "White(x)" and "White(y)," respectively.

When specifying the color temperature, set the color temperature in units of 100 K or select a color temperature according to each standard.

Note
  • When color coordinates are specified, the color temperature is changed to "User."
Target Settings - White Point - White(x) / White(y)

Settings: "0.2400" – "0.4500"

For more information, see Target Settings - White Point - Temperature.

Target Settings - Gamma (EOTF) - Gamma (EOTF)

Settings: "1.00" – "2.70" / "sRGB" / "EBU(2.35)" / "L*" / "PQ" / "HLG" / "User" / "Fixed"

Set the gamma that will be used as the calibration target for SelfCalibration.

Set the gamma, or select the gamma curve defined by each standard.

Note
  • "Gamma (EOTF)" becomes "Fixed" when adjusting with ColorNavigator 7.
Target Settings - Gamma (EOTF) - Gamma Policy

Settings: "Standard" / "Gray Balance" / "Fixed Gamma"

Select the gamma adjustment method for SelfCalibration.

Attention
  • If "HLG" is specified for "Gamma (EOTF)," "Fixed Gamma" is selected and this setting cannot be changed.
  • With "Gray Balance," all points of the grayscale are adjusted toward the target white point. Select this to prioritize whiteness when correcting the middle tone area. However, the following restrictions apply when "Gray Balance" is selected:
  • The contrast may decrease.
  • The color gamut may be narrower than when adjusting with "Fixed Gamma."
Target Settings - Gamma (EOTF) - PQ Option

Settings: "300cd/㎡ Clipping" / "500cd/㎡ Emulation" / "1000cd/㎡ Emulation" / "4000cd/㎡ Emulation" / "10000cd/㎡ Emulation"

Set the PQ option that will be used as the calibration target for SelfCalibration.

Note
  • This can be set when "PQ" is specified for "Gamma (EOTF)."
Target Settings - Gamma (EOTF) - HLG Option

Settings: "Off" / "HLG300"

Set the HLG option that will be used as the calibration target for SelfCalibration.

Note
  • This can be set when "HLG" is specified for "Gamma (EOTF)."
Target Settings - Gamma (EOTF) - HLG System Gamma

Settings: "1.0" – "1.5"

Set the HLG system gamma that will be used as a calibration target for SelfCalibration.

Note
  • This can be set when "HLG" is specified for "Gamma (EOTF)."
Target Settings - Color Gamut - Color Gamut

Settings: "Native" / "Adobe RGB" / "sRGB" / "EBU" / "BT.709" / "BT.2020" / "SMPTE-C" / "DCI-P3" / "User"

Set the color gamut that will be used as a calibration target for SelfCalibration.

In "Color Gamut," the color gamut defined by each standard can be selected.

To set a color gamut other than those specified by each standard, specify the color coordinates of each RGB color, and the display method ("Gamut Clipping") of colors outside the color gamut of the monitor.

Note
  • When you select "Color Gamut" in "Native," the preset color gamut of the LCD panel is displayed.
  • When color coordinates are specified in the color gamut settings, the "Color Gamut" is changed to "User."
Target Settings - Color Gamut - Red(x) / Red(y) / Green(x) / Green(y) / Blue(x) / Blue(y)

Settings: "0.0000" – "1.0000"

For more information, see Target Settings - Color Gamut - Color Gamut.

Target Settings - Gamut Clipping

Settings: "On" / "Off"

For more information, see Target Settings - Color Gamut - Color Gamut.

Target Settings - Advanced Settings - Limited (109% White)

Settings: "On" / "Off"

If this function is set to "On" then, if "Gamma (EOTF)" is from "1.6" to "2.7," the brightness range of the input signal is displayed as 16 – 254 (10 bits: 64 – 1019). If "Gamma (EOTF)" is anything other than "1.6" to "2.7," it is displayed as 16 – 235 (10 bits: 64 – 940).

Note
  • This can be set when "1.00 to 2.70" is specified for "Gamma (EOTF)."
Target Settings - Reset

Resets any calibration targets for the currently selected color mode back to the default settings.

Execute Calibration

SelfCalibration can be executed manually regardless of the schedule.

SelfCalibration

See SelfCalibration Functions.

Screen

Set the details regarding input signal, such as the screen size and color format.

Picture Expansion

Settings: "Auto*1" / "Full Screen" / "Aspect Ratio" / "Dot by Dot"

  1. Only available during HDMI signal input

The screen size of the monitor display can be changed.

Note
  • Setting example

BT.709 Gamut Warning

Settings: "Off" / "Clip" / "On"

If a signal that complies with the ITU-R BT.2020 standard is input, you can set the display method for colors that exceed the color gamut for the BT.709 standard.

Note
  • This function can be set only when Color Gamut is set to "BT.2020."
  • This function and "Luminance Warning" cannot be enabled at the same time. If this function is set to "On" or "Clip," the "Luminance Warning" function is automatically set to "Off."

Luminance Warning

Settings: "Off" / "On(Yellow)" / "On(Magenta)"

You can check areas with a brightness that is higher than the brightness that is set for "PQ Option" for the input signal (areas where clipping occurs).

Note
  • This function and "BT.709 Gamut Warning" cannot be enabled at the same time. If this function is set to "On", the "BT.709 Gamut Warning" function is automatically set to "Off".

Marker - Marker 1

Settings: "Off" / "On" / "On (3 division grid)"

If this function is set to "On", markers are displayed. If "On (3 division grid)" is set, boundary lines are displayed that divide the image into three equal parts with Marker 1 and Marker 1.

Note
  • If "On (3 division grid)" is set, "Marker 2" and "Marker 3" are disabled.

Marker - Marker 2 / Marker 3

Settings: "Off" / "On"

If this function is set to "On", markers are displayed.

Marker - Marker 1 Settings / Marker 2 Settings / Marker 3 Settings - Type

Settings: "Aspect" / "Dots (Center)" / "Dots (Free)"

You can select the type (method to specify position and size) of the marker.

Marker - Marker 1 Settings / Marker 2 Settings / Marker 3 Settings - Aspect

Settings: "4:3" / "13:9" / "14:9" / "15:9" / "16:9" / "21:9" / "1.85:1" / "2.35:1" / "2.39:1" / "User"

You can set the aspect ratio for the displayed marker.

Marker - Marker 1 Settings / Marker 2 Settings / Marker 3 Settings - Aspect (User)

Settings: "1.00:1" – "3.00:1"

You can set the aspect ratio for the displayed marker freely. This can only be set when "User" is selected for "Aspect".

Marker - Marker 1 Settings / Marker 2 Settings / Marker 3 Settings - Area Size

Settings: "50.0%" – "100.0%" / "User"

You can set the size of the area. This can only be set when "Aspect" is selected for "Type".

Marker - Marker 1 Settings / Marker 2 Settings / Marker 3 Settings - Hor. Position

Settings: "*1"

You can set the horizontal position of the marker. This can only be set when "Dots (Free)" is selected for "Type".

  1. The values that can be set may differ depending on the resolution of the input signal.

Marker - Marker 1 Settings / Marker 2 Settings / Marker 3 Settings - Ver. Position

Settings: "*1"

Sets the vertical position of the marker. This can only be set when "Dots (Free)" is selected for "Type".

  1. The values that can be set may differ depending on the resolution of the input signal.

Marker - Marker 1 Settings / Marker 2 Settings / Marker 3 Settings - Width

Settings: "*1"

Sets the width of the marker. This can only be set when "Dots (Free)" or "Dots (Center)" is selected for "Type", or when "Aspect" is selected for "Type" and "User" is selected for "Area Size".

  1. The values that can be set may differ depending on the resolution of the input signal.

Marker - Marker 1 Settings / Marker 2 Settings / Marker 3 Settings - Height

Settings: "*1"

You can set the vertical position of the marker. This can only be set when "Dots (Free)" or "Dots (Center)" is selected for "Type", or when "Aspect" is selected for "Type" and "User" is selected for "Area Size".

  1. The values that can be set may differ depending on the resolution of the input signal.

Marker - Marker1Settings / Marker2Settings / Marker3Settings - Thickness

Settings: "1 dot" – "6 dots"

You can set the thickness of the marker.

Marker - Marker 1 Settings / Marker 2 Settings / Marker 3 Settings - Color

Settings: "White" / "Red" / "Green" / "Blue" / "Cyan" / "Magenta" / "Yellow" / "Gray"

You can set the color of the marker.

Preferences

The monitor settings can be configured to suit your usage environment or preferences.

Menu Rotation

Settings: "" / "90°"

When the monitor is used in a portrait position, the direction of the Setting menu can also be changed.

Note
  • Check whether the cables are connected properly.
  • It is necessary to configure the settings of the external device to use the monitor in a portrait position. For details, refer to our web site (www.eizoglobal.com ).

Power Save

Settings: "On" / "Off"

This function allows you to set the monitor to the power saving mode, depending on the state of the external device connected to it.

The monitor changes to power saving mode about 15 seconds after signal input ceases to be detected. When the monitor has shifted to power saving mode, images are not displayed on the screen.

Note
  • At the time of shifting to power saving mode, a message that indicates the transition is displayed five seconds in advance.
  • When not using the monitor, you can turn off the main power supply or disconnect the power plug so that the power is cut completely.
  • Even if the monitor shifts to power saving mode, devices connected to the USB downstream port will still work. In addition, power is supplied to devices connected to the USB-C connector. Therefore, power consumption of the monitor varies depending on the connected devices, even in power saving mode.

Indicator

Settings: "Off" / "1" – "7"

The brightness of the power button and the control buttons when the screen is displayed can be set.

Beep

Settings: "On" / "Off"

The sound played when switches are used can be set.

Input Skip

Settings: "Skip" / "-"

This function allows skipping of input signals that will not be used when the input signals are switched.

Note
  • Not all input signals can be set to "Skip."

Mode Skip

Settings: "Skip" / "-"

This function allows skipping of modes that will not be used when selecting modes. Please use this function if display modes are limited, or if you want to prevent randomly changing the display status.

Note
  • Not all modes can be set to "Skip."

Custom Key - [F1]

Settings: "Off" / "Input Range" / "BT.709 Gamut Warning" / "Luminance Warning" / "Prev. Color Mode" / "Information" / "Marker1" / "Marker2" / "Marker3" / "PQ Option" / "HLG Option" / "Pixel Inspection"

You can set the function that is assigned to the [F1] key.

Note
  • By default, this key is set to "Information."
  • Regarding the custom keys, see Custom Key Settings.

Custom Key - [F2]

Settings: "Off" / "Input Range" / "BT.709 Gamut Warning" / "Luminance Warning" / "Prev. Color Mode" / "Information" / "Marker1" / "Marker2" / "Marker3" / "PQ Option" / "HLG Option" / "Pixel Inspection"

You can set the function that is assigned to the [F2] key.

Note

USB Selection - HDMI / DisplayPort / USB-C

Settings: "USB-C" / "USB-B"

If two external devices are connected to a single monitor, then the input signals and USB upstream ports can be linked. This means that the USB port will automatically switch when the input signal is switched. There is no need to re-connect the USB cable even when calibrating a single monitor using two external devices. In addition, USB devices such as a mouse or keyboard can be connected to the monitor and used with two external devices.

Default settings differ depending on the input signal.

Input signal

Default settings

HDMI, DisplayPort

USB-B

USB-C

USB-C

Note
  • Before changing the setting, remove all connected USB memory devices from the monitor. Otherwise, data may be lost or damaged.
  • The USB downstream port operates from the external device being displayed.

Monitor Reset

Restores all settings to their default settings except for the following settings:

Languages

Settings: "English" / "German" / "French" / "Spanish" / "Italian" / "Swedish" / "Japanese" / "Simplified Chinese" / "Traditional Chinese"

The display language for menus and messages can be selected.

Information

You can check the monitor information (model name, serial number (S/N), firmware version, usage time) and the input signal information.

Example: